A1000 AC Drive – Network Communications Options

A1000 600V AC DriveA1000 600V AC Variable Frequency Drive

1-30 Horsepower
The Drive for the Future . . . Today

 

Network Communications Options for A1000 600V Drive

These communication cards provide the interface between industrial networks and Yaskawa AC drives. These options may be factory installed or field installed.

Compare this drive’s Network Communications Options to other Yaskawa AC drives.

Network Communications Option Option Card #
& Mounting Location
Installation Manual Technical Manual & Latest Support File
DeviceNetâ„¢ With ADR – Each DeviceNet network supports up to 63 drives. Controllers are available from many PLC and/or PC suppliers. The DeviceNet network communications option board is designed to comply with all pertinent aspects of the ODVA (Open DeviceNet Vendor Association) specification and AC drive profile. All parameters, diagnostics, and operational commands are accessible via DeviceNet. Automatic Device Replacement (ADR) is supported in this DeviceNet option, including the functions of Auto Baud Rate sensing and Faulted Node Recovery (using Group 4 messaging). The DeviceNet satellite board mounts integrally in the drive and provides a DeviceNet standard open tap connector. Electronic Data Sheets (EDS) may be downloaded to assist with network configuration and drive setup. SI-N3
CN5-A
TOBPC73060043 SIEPC73060043
EDS File
EtherNet/IP – This option complies with the EtherNet/IP protocol specification. This allows for communication over 10/100 Mbps Ethernet networks. This option has the ability to configure the IP Address from a user specified IP address, from a DHCP host, or from a BootP host. All parameters, diagnostics and operational commands are accessible via EtherNet/IP. Auto-tuning the motor is also possible through this option using the DriveWizard PC program. SI-EN3
CN5-A
TOEPYEACOM04 SIEPYEACOM04
EDS File
MECHATROLINK-II – This option is designed for connecting a drive to a field network using the MECHATROLINK protocol. The MECHATROLINK-II option allows the user to operate the drive, monitor the status, and change parameters from a MECHATROLINK master device at a communication speed up to 10Mbps. SI-T3
CN5-A
TOBPC73060050 SIEPC73060050
Modbus TCP/IP – This option complies with the Modbus TCP/IP protocol specification. This allows for Modbus communication over 10/100 Mbps Ethernet networks. This option has the ability to configure the IP Address from a user specified IP address, from a DHCP host, or from a BootP host. All parameters, diagnostics and operational commands are accessible via Modbus TCP/IP. Auto-tuning the motor is also possible through this option using the DriveWizard PC program. This option supports up to 10 simultaneous PLC/PC connections. SI-EM3
CN5-A
TOEPYEACOM05 SIEPYEACOM05
Modbus RTU RS-232 – Complies with a subset of Modicon’s Modbus RTU specification, referred to as Memobus by Yaskawa. All parameters, diagnostics and operational commands are accessible. The RS-232 Modbus RTU network allows for one drive to be accessed by the controller. Embedded
CN2-2
N/A SIEPC71061631
Modbus RTU RS-485 – Complies with a subset of Modicon’s Modbus RTU specification, referred to as Memobus by Yaskawa. All parameters, diagnostics and operational commands are accessible. Each RS-485 Modbus RTU network supports up to 32 drives. Embedded
Terminal Strip
N/A SIEPC71061631
PROFIBUS-DP – This option complies with the Profibus- DP protocol specification. All parameters, diagnostics and operational commands are accessible via Profibus. The option board provides a 9-pin (F) type D-Sub connector for easily connecting to a standard Profibus style, shielded twisted-pair cable. Each Profibus network supports up to 99 drives. This option supports all of the Profibus data rates from 9.6 Kbps to 12 Mbps. Up to 32 bytes of input data and 32 bytes of output data are provided per message transaction. Sync and Freeze modes are supported for groups. Profibus DP-V1 support (cyclic and acyclic data exchange). Configurable PPO read and write parameters. The option is configured using parameters within the drive, which allows for easy configuration eliminating the use of hardware switches. Status LEDs are viewable through the front cover, and a monitor has been added to allow for improved diagnostics. SI-P3
CN5-A
TOBPC73060042 SIEPC73060042
GSD File

Download communications software files from this website through the Downloads section/Network Support Files.

 

Copyright © 2010 Yaskawa Electric America, Inc. All Rights Reserved.